Hi,欢迎访问北京北广精仪仪器设备有限公司

北京北广精仪仪器设备有限公司

江源摩擦磨损量试验机工厂

联系我们
  • 北京北广精仪仪器设备有限公司
  • 陈丹
联系方式
北京北广精仪仪器设备有限公司
  • 联 系 人:陈丹
  • 手 机 号:
  • 公司电话:
  • 公司地址:北京
文章详情

江源摩擦磨损量试验机工厂

发布用户:Bgjy 时间:2021-11-26 10:17

江源摩擦磨损量试验机工厂

江源摩擦磨损量试验机工厂


产品名称:塑料滑动摩擦磨损试验机

型号:M-200 特点:本机采用高精度扭矩传感器,嵌入式中央单元处理系统cpu控制,支持xp  win7. win8.  win10系统,软件实时绘制显示扭矩-时间曲线、摩擦系数-时间曲线,绘制摩擦力、摩擦系数、磨损量等曲线变化,可设定试验次数,显示当前试验次数,设定时间及当前试验时间等多种功能;

本机具有一次设置,全自动运行,实验结束后自动停机,并检测磨损程度;

配有彩色打印机,可以打印出带有曲线,表格数据,试验单位名称等精美的试验报告单。另外本仪器配有故障自动报警系统问题报警灯和软件报警灯同时提示出现问题时间保护仪器以免零件损坏。是各个科研单位,大学,企业实验室的必备检测设备。

江源摩擦磨损量试验机工厂

伺服电机一个(惠斯通)

使用说明书一份;One copy of the instructions;

塑料名称、规格、牌号、生产厂;A. plastic name, specification, brand and manufacturer;

9退出功能: 退出系统。

砝码重量:4KG砝码一件,1KG砝码4件,可实现重量叠加功能。

计算机数据采集卡一块;A piece of computer data acquisition card;

系统运行稳定,可靠性高。The system runs steadily and has high reliability.

标准摩擦环二件;Two standard friction rings;

主要配置:

试验主机一台;Test host one;

江源摩擦磨损量试验机工厂

试验结果:磨痕宽度或体积磨损及摩擦系数的测定结果;F. test results: test results of wear mark width or volume wear and friction coefficient;

试验主机一台;Test host one;

设定时间及当前试验时间等多种功能,随机配备彩色打印机,可以打印出带有曲线、表格数据等标准要求的试验报告。Set time, current test time and other functions, equipped with color printer, can print out test report with curve, table data and other standard requirements.

高精度扭矩传感器一只;High pcision torque sensor one;

砝码重量:4KG砝码一件,1KG砝码4件,可实现重量叠加功能。

产品合格证一份;A copy of the product certificate;

摩擦力矩: 0--4N·m ±0.5%

注:圆环材质也可按产品标准另定。Note: the ring material can also be determined according to the product standard.

试验日期、人员。G. test date and personnel.

摩擦环尺寸:≥¢40×10mm ,倒角≥0.5×45°,外圆表面与内圆同心度偏差≤0.01;the size of the friction ring is greater than or equal to 40 x 10mm, the chamfering is equal to 0.5 x 45 degrees, and the concentricity deviation between the outer surface and the inner circle is less than 0.摩擦环材质:45 号钢;friction ring material: No. 45 steel;

江源摩擦磨损量试验机工厂

摩擦环尺寸:¢40×10mm 倒角0.5×45°外圆表面与内圆同心度偏差小于0.01

测定和记录摩擦力矩系统,精确到5%以内。Measure and record the friction torque system to within 5%.

转动速度: 0-200转/分 连续可调到500转/分

复合材料滑动摩擦磨损试验机  技术参数Technical parameters:  M-200

产品使用说明书一份

摩擦环尺寸:≥¢40×10mm ,倒角≥0.5×45°,外圆表面与内圆同心度偏差≤0.01;the size of the friction ring is greater than or equal to 40 x 10mm, the chamfering is equal to 0.5 x 45 degrees, and the concentricity deviation between the outer surface and the inner circle is less than 0.摩擦环材质:45 号钢;friction ring material: No. 45 steel;

试验负荷;E. test load;

转动速度rotation speed: ≤200 转/分(可调adjustable);

传感器测量精度:1% FS

标准摩擦环二件;Two standard friction rings;

江源摩擦磨损量试验机工厂

负荷精度:0.5%

可以通过此界面管理使用此设备的人员信息,可以创建用户,删除用户,查看用户密码(对管理员),修改用户密码。

供电电源 (鸿海)

加载系统,对试样和圆环,可施加法向力,精确到5%以内。Loading system, for the sample and the ring, the additional force can be applied, accurate to within 5%.

主要配置:

注:试验设备本标准推荐采用M-200型磨损试验机。Note: M-200 wear testing machine is recommended in this standard.

实时显示摩擦系数-时间,扭矩-时间曲线。 real-time display of friction coefficient time, torque time curve.

本试验中圆环的材质对塑料磨损试验结果影响很大,因此本标准采用的圆环,其外形尺寸见The material of the ring in this test has a great influence on the plastic wear test results. Therefore, the ring adopted in this standard has the dimensions shown in Figure 材料为45号钢,圆环要求整体淬火,热处理HRC 40~外圆表面光洁度▽倒角处均为0.5×45度,外圆表面与内圆同心度偏差小于0.he material is 45 steel, the ring is required to be quenched as a whole, the heat treatment is HRC 40- the surface finish of the outer circle is ▽ the chamfering is 0.5 × 45 degree, and the concentricity deviation between the outer circle surface and the inner circle is less than 0.    圆环可以反复使用,每次试验后,需重新磨削。当外径小于36毫米就不能再用。作仲裁试验时用直径40毫米的圆环。The ring can be used repeatedly. After each test, it needs to be grinded again. When the outer diameter is less than 36 mm, it can not be reused. A ring with a diameter of 40 mm must be used for the arbitration test.

计数器精度:1S

摩擦力矩: 0—4N.m;friction torque: 0 - 4N.m;

江源摩擦磨损量试验机工厂

试验结果:磨痕宽度或体积磨损及摩擦系数的测定结果;F. test results: test results of wear mark width or volume wear and friction coefficient;

摩擦环尺寸:≥¢40×10mm ,倒角≥0.5×45°,外圆表面与内圆同心度偏差≤0.01;the size of the friction ring is greater than or equal to 40 x 10mm, the chamfering is equal to 0.5 x 45 degrees, and the concentricity deviation between the outer surface and the inner circle is less than 0.摩擦环材质:45 号钢;friction ring material: No. 45 steel;

整机重量:约45公斤试验条件Test conditions

管理:可对使用些设备的用户进行管理。退出:退出操作系统。

试验报告应包括下列内容:The test report shall include the following contents:

设置:对试验的参数进行设置,如试验速度,试验数据等。 开始:开始进行试验。

精度:速度精度:1%

负荷load: (20KG)196N ± 0.1%,可增至(40KG)392N;

摩擦力矩: 0--4N·m ±0.5%

电源线:接入电源线插口

江源摩擦磨损量试验机工厂

负 荷: 196N ± 0.2%(可扩充到392N)

使用说明书一份;One copy of the instructions;

计数器精度:1S

管理:可对使用些设备的用户进行管理。退出:退出操作系统。

试验报告Test report

停止:停止试验,试验结束。打印:打印试验报告。

试验报告可打印试验参数,试验数据,曲线,备注等信息,简单,方便,可编辑。The test report can print experimental parameters, test data, curves, remarks and other information. It is simple, convenient and editable.

试样夹具结构和尺寸见图并附配垫圈 4 GB 848-沉头螺钉M3×0.35长10毫米。要保证试样安置后无轴向窜动。See Fig. 2 for the structure and dimension of the sample clamp, with washer 4 GB 848- countersunk screw m3 × 0.35 with length of 10 mm. Ensure that there is no axial movement after the sample is placed.

主要技术指标:

传动系统,用来带动圆环以给定的转速旋转,精确到5%以内,并要求圆环安装部位轴的径向跳动小于0.01毫米。The transmission system is used to drive the ring to rotate at a given speed, accurate to within 5%, and the radial runout of the shaft at the installation ition of the ring is required to be less than 0.01mm.

试样的制备方法,摩擦表面状况,测定的试样个数;B. pparation method of sample, friction surface condition, number of samples measured;

保存:完成试验后可保存试验数据。

江源摩擦磨损量试验机工厂

负荷精度:0.5%

本试验中圆环的材质对塑料磨损试验结果影响很大,因此本标准采用的圆环,其外形尺寸见The material of the ring in this test has a great influence on the plastic wear test results. Therefore, the ring adopted in this standard has the dimensions shown in Figure 材料为45号钢,圆环要求整体淬火,热处理HRC 40~外圆表面光洁度▽倒角处均为0.5×45度,外圆表面与内圆同心度偏差小于0.he material is 45 steel, the ring is required to be quenched as a whole, the heat treatment is HRC 40- the surface finish of the outer circle is ▽ the chamfering is 0.5 × 45 degree, and the concentricity deviation between the outer circle surface and the inner circle is less than 0.    圆环可以反复使用,每次试验后,需重新磨削。当外径小于36毫米就不能再用。作仲裁试验时用直径40毫米的圆环。The ring can be used repeatedly. After each test, it needs to be grinded again. When the outer diameter is less than 36 mm, it can not be reused. A ring with a diameter of 40 mm must be used for the arbitration test.

主机一台(北京北广)

控制线:一头接设备,一头接电脑上边串口复合材料滑动摩擦磨损试验机 本仪器融合了当前 的智能电路系统进行控制,并结合老式M-200摩擦磨损试验机的功能进行改造而成,本仪器具有测控精度高,操作便捷等优势,是科研院所、质检机构、实验室研究的试验设备。

产品装箱单一份

试样尺寸: 30mm×7mm×6mm; sample size: 30mm x 7mm x 6mm;

环境温度、温度及状态调节条件;C. environment temperature, temperature and state regulation conditions;

使用说明书一份;One copy of the instructions;

高精度扭矩传感器一只(固尔)

标准摩擦环二件;Two standard friction rings;

江源摩擦磨损量试验机工厂